Golden-lighting 1993-BA3 PS User Manual Page 1

Browse online or download User Manual for Lighting Golden-lighting 1993-BA3 PS. Golden Lighting 1993-BA3 PS User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 1
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Assembly Instructions: 1993-BA3 PS (Joia)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit
breakerandcompletelyremovetheoldxturefromthewall,
including the old mounting strap.
Mounting strap (B) contains several pairs of threaded holes.
Find the pair of holes that matches the spacing of the holes
onthejunctionboxandyourxturebackplate.Twoof
mounting screws (A) should be attached to mounting strap
(B). You may need to tighten the nuts that hold these screws
in place. Pull the house wires through the center of mounting
strap(B),placemountingstrap(B)overthejunctionboxso
thatmountingscrews(A)arehorizontal,andinalignment
withtheholelocationsonxturebackplate(F).Secure
mountingstrap(B)tothejunctionboxwithmountingscrews
(D) and a screwdriver. Tighten the screws securely.
CONNECTING THE WIRES
Attachthexture’swirestothepowersupplywiresfromthe
junctionbox.Connectblacktoblack(orsmooth);whiteto
white(orribbed);groundtoground(greenorcopper).Twist
theendsofthewirepairstogether,thentwistonawire
connector. Make sure all twists are in the same direction. If
there is no ground wire (green or copper) from the junction
box,locategroundscrew(E)onmountingstrap(B)and
wrapthexturegroundwirearoundthegreengroundscrew
(E). Use a screwdriver to secure ground screw (E) onto the
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Placexturebackplate(F)overmountingscrews(A)sothat
they protrude through the holes in the front of the backplate.
Thread deco nuts (G) onto mounting screws (A). Twist until
thebackplateofthextureissnugagainstthewall.
Slideglassshades(I)overthesockets.Tosecureinplace,
place spacers (J) over the sockets before using socket tool
(M) to twist socket rings (K) onto the threads of the sockets.
Install the provided halogen bulbs (L) in accordance with the
xture’sspecications.
Bulb Note: Use a tissue or paper towel to hold the bulb and
push the bulb down into the socket. Oils and dirt can cause
the bulb life to shorten. Rubbing alcohol is recommended for
cleaning the bulbs.
Your installation is now complete. Turn on the power and test
thexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down
the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the
light and remove the glass prior to cleaning. Place the glass shades aside to clean one at a time. Hand wash glass with warm water
and mild detergent. Dry with a lint-free or microber cloth.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
B
A
C
H
I
J
F
D
E
G
K
L
M
Page view 0
1

Summary of Contents

Page 1 - CLEANING TIPS

Assembly Instructions: 1993-BA3 PS (Joia)IMPORTANT: • ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL. • SHUT OFF POWER SUPPLY AT FU

Comments to this Manuals

No comments